There was a serial system handshake error. ID = %d
Serial port status error. ID = %d Reference: %d. Are you printing out of the same port you are using for PC emulation? Check the Chooser and Hardware Options Menu for conflicts.
There was an error reading data from serial port number %d. ID= %d
An unkown event for the serial communications emulator was received. The event number was: %d
Error writting to Macintosh serial driver. Error code: %d
Open error: RAM component of serial driver B. Error code: %d
Open error: RAM component of serial driver A. Error code: %d
Error while trying to open serial port B for output. Error code: %d
Error while trying to open serial port B for input. Error code: %d
Error while trying to open the serial port A for output. Error code: %d
Error while trying to open the serial port A for input. Error code: %d
Port B (the printer port) is in already in use is not available for PC Com port emulation. Please check for conflicts.
Port A (the phone port) is in already in use is not available for PC Com port emulation. Please check for conflicts.
The printer port seems to be in use by AppleTalk. It cannot be used for PC Com port emulation. Check The Chooser and the Hardware Options menu for conflicts.
The phone port seems to be in use by AppleTalk. It cannot be used for PC Com port emulation. Check The Chooser and the Hardware Options menu for conflicts.
Error removing from Slot Manager. ID = %d
Error installing into Slot Manager. ID = %d
Dmapgat trying to field a write to %h which is outside DMA page register range.
There is no room for the co-processor device driver. Remove some desk accessories and try again.
There was an error trying to get all of memory so that I could split it up between the PC and the Macintosh.
There was an error trying to put PC memory in the correct place so that I could use it.
There was an error allocating memory for the PC to use.
Sorry, there is not enough memory to run PC software on this machine.
Emldrvdw: Unknown access request type = %d.
Emldrvd: Unknown command from PC. ID = %d.
Emldrived: Unknown Msg_Type received: %d
EmldriveD: Net Hdw Hdr type not DOS to HOST. It was %d.
Unknown response: %d received from Drive D: device emulator.
Tried to write %d byte(s) to MS-DOS Print file, but instead wrote %d byte(s).
Printing error: %d
Error trying to reset the printing device driver. ID = %d
Error trying to write the printing device driver. ID = %d
Error trying to open the printing device driver. ID = %d
A printer has not been selected using Chooser. ID = %d
Access permission has been denied to the MS-DOS print file.
The volume for the MS-DOS print file is write protected by hardware.
The volume for the MS-DOS print file has been locked by software.
There has been an I/O Error while writing the MS-DOS print file. Purge this print file and start again.
The MS-DOS print file is locked. Purge this print file and start again.
The disk is full. Cannot write to MS-DOS print file. Purge this print file and start again.
Error trying to read the MS-DOS print file. ID = %d
Error trying to delete MS-DOS print file. ID = %d
Error trying to close MS-DOS print file. ID = %d
Error trying to create MS-DOS print file. ID = %d
The file you have selected for printing is not an MS-DOS print file.
Error trying to get information on MS-DOS print file. ID = %d
Error seeking in MS-DOS printing file. ID = %d
Error opening MS-DOS printing file. ID = %d
There was an error while trying to write to the Macintosh sound driver. ID = %d
Cannot allocate D: i/o buffer.
Drive_C: Chopdisk...Unable to truncate file. Oserr is %d.
Drive C: Chopdisk...Cannot determine last sector in use.
Drive C: Chopdisk...Unable to read FAT. Oserr is %d.
Drive C: Chopdisk...Unable to allocate memory for FAT image.
Drive C: Chopdisk... Unable to read boot record, OSerr is %d.
Drive C: Chopdisk... Cannot determine partition to use.